? coilcraft, inc. 2011 specifications subject to change without notice. please check our website for latest information. maxi spring ? air core inductors document 185-1 document 185-1 revised 01/11/11 inductance 2 percent q 2 q 2 test freq. srf min 4 dcr max 5 i rms 6 part number 1 turns (nh) tolerance 3 typ min (mhz) (ghz) (mohm) (a) 132-09sm_l_ 9 90 5,2 114 95 50 1.140 15 3.5 132-10sm_l_ 10 111 5,2 104 87 50 1.020 15 3.5 132-11sm_l_ 11 130 5,2 104 87 50 0.900 20 3.0 132-12sm_l_ 12 169 5,2 114 95 50 0.875 25 3.0 132-13sm_l_ 13 206 5,2 114 95 50 0.800 30 3.0 132-14sm_l_ 14 222 5,2 110 92 50 0.730 35 3.0 132-15sm_l_ 15 246 5,2 114 95 50 0.685 35 3.0 132-16sm_l_ 16 307 5,2 114 95 50 0.660 35 3.0 132-17sm_l_ 17 380 5,2 114 95 50 0.590 50 2.5 132-18sm_l_ 18 422 5,2 114 95 50 0.540 60 2.5 132-19sm_l_ 19 491 5,2 114 95 50 0.535 65 2.0 132-20sm_l_ 20 538 5,2 104 87 50 0.490 90 2.0 1. when ordering, specify tolerance, termination and packaging codes: 132-20sm gld termination: l = rohs compliant tin-silver (96.5/3.5) over copper. special order: t = rohs tin-silver-copper (95.5/4/0.5) or s = non-rohs tin-lead (63/37). tolerance: g =2% j = 5% packaging: d = 13 machine-ready reel. eia-481 embossed plastic tape (800 parts per full reel). b = less than full reel. in tape, but not machine-ready. to have a leader and trailer added ($25 charge), use code letter d instead. 2. inductance and q tested at 50 mhz on an agilent/hp 4291a with a 16193 fixture and correlation. 3. tolerances in bold are stocked for immediate shipment. 4. srf tested on the agilent/hp 8753d and a coilcraft ccf1248 test fixture. 5. dcr tested on the cambridge technology model 510 micro ohmmeter. 6. current that causes a 15c temperature rise from 25c ambient. 7. electrical specifications at 25c. see qualification standards section for environmental and test data. refer to doc 362 ?soldering surface mount components? before soldering. weight 0.42 ? 0.59 g terminations rohs compliant tin-silver over copper. other terminations available at additional cost. ambient temperature ?40c to +125c with i rms current, +125c to +140c with derated current storage temperature component: ?40c to +140c. packaging: ?40c to +80c resistance to soldering heat max three 40 second reflows at +260c, parts cooled to room temperature between cycles temperature coefficient of inductance (tcl) +5 to +70 ppm/c moisture sensitivity level (msl) 1 (unlimited floor life at <30c / 85% relative humidity) failures in time (fit) / mean time between failures (mtbf) one per billion hours / one billion hours, calculated per telcordia sr-332 packaging 800/13 reel plastic tape: 24 mm wide, 0.3 mm thick, 12 mm pocket spacing, 6.1 mm pocket depth pcb washing only pure water or alcohol recommended ? air core inductors feature higher q, l and current ratings ? rigid package provides a flat surface for pick and place ? leads are locked in position for precise terminal spacing
? coilcraft, inc. 2011 specifications subject to change without notice. please check our website for latest information. document 185-2 document 185-2 revised 01/11/11 maxi spring? air core inductors typical l vs frequency typical q vs frequency 1 10 frequency (mhz) inductance (nh) 100 1000 90 nh 246 nh 422 nh 169 nh 1000 900 800 700 600 500 400 300 200 100 0 110 frequency (mhz) q factor 100 1000 90 nh 246 nh 422 nh 169 nh 250 200 150 100 50 0 135 max 0 min recommended land pattern strip length 0.095 2,42 0.185 4,70 0.080 2,04 0.314 7,98 0.415 0.260 0.235 0.314 0.020 a max b max c max d e 0.240 0.015 10,55 6,60 5,97 6,10 0,38 7,98 0,51 e b d c a -40 -20 0 20 40 60 80 100 140 120 ambient temperature (c) 120 110 100 90 80 70 60 50 40 30 20 10 0 percent of rated rms i 25c typical irms derating dimensions are in inches mm designer?s kit c319 contains 8 each of all 5% values. designer?s kit c319-2 contains 8 each of all 2% values.
|
